SPLITNCV
list Vernon Everett
Hi all
Can anybody point me to some documentation about how to use SPLITNCV.
(Or perhaps you can answer my questions)
In the mailing list I have seen it as SPLITNCV, SPLIT_NCV and
SPLIT-NCV. Which is it? As in, what goes into hobbitserver.cfg?
What version of Xymon was it introduced? I can't seem to get it
working here, so I might need an upgrade, or was this feature only
ever delivered in a patch?
Regards
Vernon
list Neil Franken
Here is a sample of how I use it. SQLTPS = ncv NCV_SQLTPS="Transactions:GAUGE" This worked for me over several releases.
▸
-----Original Message-----
From: Vernon Everett [mailto:user-b3f8dacb72c8@xymon.invalid]
Sent: 06 July 2010 08:40 AM
To: user-ae9b8668bcde@xymon.invalid
Subject: [hobbit] SPLITNCV
Hi all
Can anybody point me to some documentation about how to use SPLITNCV.
(Or perhaps you can answer my questions)
In the mailing list I have seen it as SPLITNCV, SPLIT_NCV and
SPLIT-NCV. Which is it? As in, what goes into hobbitserver.cfg?
What version of Xymon was it introduced? I can't seem to get it
working here, so I might need an upgrade, or was this feature only
ever delivered in a patch?
Regards
Vernon
list Vernon Everett
OK. Did a little trial and error.
It's SPLITNCV_testname
And we use GRAPH to control the number of lines on a graph.
GRAPH="blah blah,stuff,testname::4"
This should give me 4 lines per graph in trends.
It gives me 3 :-(
testname::5 gives me the 4 lines I was looking for.
Anybody else seen this behaviour?
Next question though. testname::X controls the number of lines on the
trends page.
How do I limit the number of lines on the actual testname page?
Right now it's showing the lot on one graph, and it's mega fugly.
Regards
Vernon
▸
On Tue, Jul 6, 2010 at 2:40 PM, Vernon Everett <user-b3f8dacb72c8@xymon.invalid> wrote:Hi all Can anybody point me to some documentation about how to use SPLITNCV. (Or perhaps you can answer my questions) In the mailing list I have seen it as SPLITNCV, SPLIT_NCV and SPLIT-NCV. Which is it? As in, what goes into hobbitserver.cfg? What version of Xymon was it introduced? I can't seem to get it working here, so I might need an upgrade, or was this feature only ever delivered in a patch? Regards Vernon
list Vernon Everett
Hi Neil
That's NCV, and it works a treat. Been using it for years.
However, I am looking at the SPLITNCV feature.
It appears really cool on paper. I just need to make it work for me.
It will allow you to graph a previously unknown number of lines, by
putting them one per rrd file instead of all into a single rrd file.
You then generate the graphs using a wildcard in the rrd file
definition in hobbitgraph.cfg.
But like i mentioned, on the trends page it looks great.
On the test page, all the lines are on one graph. :-(
Cheers
V
On Tue, Jul 6, 2010 at 2:57 PM, Neil Franken
▸
<user-1689acfc5a3b@xymon.invalid> wrote:Here is a sample of how I use it. SQLTPS = ncv NCV_SQLTPS="Transactions:GAUGE" This worked for me over several releases. -----Original Message----- From: Vernon Everett [mailto:user-b3f8dacb72c8@xymon.invalid] Sent: 06 July 2010 08:40 AM To: user-ae9b8668bcde@xymon.invalid Subject: [hobbit] SPLITNCV Hi all Can anybody point me to some documentation about how to use SPLITNCV. (Or perhaps you can answer my questions) In the mailing list I have seen it as SPLITNCV, SPLIT_NCV and SPLIT-NCV. Which is it? As in, what goes into hobbitserver.cfg? What version of Xymon was it introduced? I can't seem to get it working here, so I might need an upgrade, or was this feature only ever delivered in a patch? Regards Vernon