bb-display and bbproxy
list Thomas Kähn
Hi,
is it possible to run bbproxy and bb-display at the same
time?
The goal is to forward messages to a main Hobbit server, but still
being able to look at the status on the proxy server.
Best regards
Thomas
--
Thomas Kähn NetCologne
Network Engineering & Design Gesellschaft für Telekommunikation mbH
Im Süsterfeld 6
Telefon: 0241/701333-18 52072 Aachen
Fax: XXXX/XXXXXX
Handelsregister: HRB 25580, Amtsgericht Köln
Geschäftsführer: Werner Hanf, Dipl.-Ing. Karl-Heinz Zankel
list Buchan Milne
On Tuesday 25 November 2008 17:02:29 Thomas Kähn wrote:
Hi, is it possible to run bbproxy and bb-display at the same time?
Yes.
list Brian O'Mahony
Im running two scripts from deadcat.net -- bb-omsa-raid.sh and openmanage.sh. Decided to implement these on a number of servers, and im seeing a few issues: 1. On PE2850s the openmanage script is showing all the information. However the Raid monitor lists the disks and the controllers but reports "no Controllers Found" 2. On PE1850 the openmanage script only picks up "Health" I assume this is picking up the CHASSIS health rather than mainsystem health? Is there a version for blades or do I go edit the script? Thx B The information in this email is confidential and may be legally privileged. It is intended solely for the addressee. Access to this email by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution or any action taken or omitted to be taken in reliance on it, is prohibited and may be unlawful. If you are not the intended addressee please contact the sender and dispose of this e-mail. Thank you.
list Ricardo Stella
The scripts on deadcat for the raid controllers does not work with later version of OMSA (at least v5). In fact it reports green condition even if you have a failed disk due to to a logic change. OMSA used to report via the controller checks about a disk being degraded. That's no longer the case. Someone posted an updated version of it in the bigbro list.. I'll try to dig a copy out otherwise. My .02...
▸
Brian O'Mahony wrote:Im running two scripts from deadcat.net -- bb-omsa-raid.sh and openmanage.sh. Decided to implement these on a number of servers, and im seeing a few issues: 1. On PE2850s the openmanage script is showing all the information. However the Raid monitor lists the disks and the controllers but reports "no Controllers Found" 2. On PE1850 the openmanage script only picks up "Health" I assume this is picking up the CHASSIS health rather than mainsystem health? Is there a version for blades or do I go edit the script? Thx B The information in this email is confidential and may be legally privileged. It is intended solely for the addressee. Access to this email by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution or any action taken or omitted to be taken in reliance on it, is prohibited and may be unlawful. If you are not the intended addressee please contact the sender and dispose of this e-mail. Thank you.
-- °(((=((===°°°(((===========================================
list Ricardo Stella
Ah - disregard this. This is the case for the windows version. The linux is ok... You might need some editing depending on the controller, OMSA and firmware you have. Usually it's a type case issue. My .02...
▸
Ricardo Stella wrote:The scripts on deadcat for the raid controllers does not work with later version of OMSA (at least v5). In fact it reports green condition even if you have a failed disk due to to a logic change. OMSA used to report via the controller checks about a disk being degraded. That's no longer the case. Someone posted an updated version of it in the bigbro list.. I'll try to dig a copy out otherwise. My .02... Brian O'Mahony wrote:Im running two scripts from deadcat.net -- bb-omsa-raid.sh and openmanage.sh. Decided to implement these on a number of servers, and im seeing a few issues: 1. On PE2850s the openmanage script is showing all the information. However the Raid monitor lists the disks and the controllers but reports "no Controllers Found" 2. On PE1850 the openmanage script only picks up "Health" I assume this is picking up the CHASSIS health rather than mainsystem health? Is there a version for blades or do I go edit the script? Thx B The information in this email is confidential and may be legally privileged. It is intended solely for the addressee. Access to this email by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution or any action taken or omitted to be taken in reliance on it, is prohibited and may be unlawful. If you are not the intended addressee please contact the sender and dispose of this e-mail. Thank you.
-- °(((=((===°°°(((===========================================
list Martin Flemming
Hi, Brian ! .. which OS and OMSA-Version are you running ? .. in my case, i've got RHEL3 and OMSA-5.1 and got also errors, but my controller will be recognized not at all ... PowerEdge 1955 SCSI storage controller: LSI Logic / Symbios Logic SAS1068 PCI-X Fusion-MPT SAS (rev 01 Product name : Server Administrator Install Core (subscription) Version : 5.1.0 .. and by the way, are all services are started ? ( /opt/dell/srvadmin/omil/supportscripts/srvadmin-services.sh ) cheers, martin
▸
On Tue, 25 Nov 2008, Brian O'Mahony wrote:
Im running two scripts from deadcat.net -- bb-omsa-raid.sh and openmanage.sh. Decided to implement these on a number of servers, and im seeing a few issues: 1. On PE2850s the openmanage script is showing all the information. However the Raid monitor lists the disks and the controllers but reports "no Controllers Found" 2. On PE1850 the openmanage script only picks up "Health" I assume this is picking up the CHASSIS health rather than mainsystem health? Is there a version for blades or do I go edit the script? Thx B The information in this email is confidential and may be legally privileged. It is intended solely for the addressee. Access to this email by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution or any action taken or omitted to be taken in reliance on it, is prohibited and may be unlawful. If you are not the intended addressee please contact the sender and dispose of this e-mail. Thank you.
Gruss
Martin Flemming
Martin Flemming
DESY / IT office : Building 2b / 008a
Notkestr. 85 phone : XXX - XXXX - XXXX
22603 Hamburg mail : user-f286aaa49a76@xymon.invalid
list Buchan Milne
▸
On Tuesday 25 November 2008 18:10:37 Brian O'Mahony wrote:
Im running two scripts from deadcat.net -- bb-omsa-raid.sh and openmanage.sh. Decided to implement these on a number of servers, and im seeing a few issues: 1. On PE2850s the openmanage script is showing all the information. However the Raid monitor lists the disks and the controllers but reports "no Controllers Found" 2. On PE1850 the openmanage script only picks up "Health" I assume this is picking up the CHASSIS health rather than mainsystem health? Is there a version for blades or do I go edit the script?
Have you tried devmon with the dell-poweredge template?
list Thomas Séglard
Hi, I rewrote a little these scripts to match my setup. Actually, I got a lot of Dell PE 1850/1950/2950 and so on... In addition, I rewrote another script to grab informations from the BMC. Please, find below the output : -=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- green Fans : Ok : omreport chassis fans green Intrusion : Ok : omreport chassis intrusion green Memory : Ok : omreport chassis memory green Processors : Ok : omreport chassis processors green Temperatures : Ok : omreport chassis temps green Voltages : Ok : omreport chassis volts green Hardware Log : Ok : none green Batteries : Ok : omreport chassis batteries -=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- green All Server Components Functional ! No need for snmp, only 'sudo' ! Obviously, the OMSA package has to be installed on your monitored servers. Sincerly, ThomaS
▸
Buchan Milne a écrit :On Tuesday 25 November 2008 18:10:37 Brian O'Mahony wrote:Im running two scripts from deadcat.net -- bb-omsa-raid.sh and openmanage.sh. Decided to implement these on a number of servers, and im seeing a few issues: 1. On PE2850s the openmanage script is showing all the information. However the Raid monitor lists the disks and the controllers but reports "no Controllers Found" 2. On PE1850 the openmanage script only picks up "Health" I assume this is picking up the CHASSIS health rather than mainsystem health? Is there a version for blades or do I go edit the script?Have you tried devmon with the dell-poweredge template?
list Thomas Kähn
Hi Buchan,
▸
On Tue, Nov 25, 2008 at 05:42:18PM +0200, Buchan Milne wrote:On Tuesday 25 November 2008 17:02:29 Thomas Kähn wrote:is it possible to run bbproxy and bb-display at the same time?Yes.
thanks for your hint regarding my problem. I've tried to run both services. However either bbproxy was not forwarding alarms (when hobbitd was running too) or the web pages on the proxy where not updated. Can you give me a short notice on how to configure bbproxy/hobbitd in order to have a normal Hobbit server running which in addition sends all messages to another Hobbit server? Do I have to set different port numbers for hobbitd and bbproxy? I've already tried to set bbproxy to 1985 which resulted in the problem described above.
▸
Best regards
Thomas
--
Thomas Kähn NetCologne
Network Engineering & Design Gesellschaft für Telekommunikation mbH
Im Süsterfeld 6
Telefon: 0241/701333-18 52072 Aachen
Fax: XXXX/XXXXXX
Handelsregister: HRB 25580, Amtsgericht Köln
Geschäftsführer: Werner Hanf, Dipl.-Ing. Karl-Heinz Zankel
list Brian O'Mahony
#1 After a bit more investigation, it turns out that it IS picking up the RAID info the 2850s. However as these have a SCSI card in them with nothing connected, its marking them as red. How do I get the script to ignore the SCSI card?
Controller 1 is being listed as:
LSI Logic PCI-X Ultra320 SCSI Host Adapter
#2 Whats weird is when I run "omreport chassis" on the balde and the 2850s I get the same output. However it seems the blades are only sending half the data.
PE2850:
[root at ccvob01_pr ~]# omreport chassis
Health
Main System Chassis
SEVERITY : COMPONENT
Ok : Fans
Ok : Intrusion
Ok : Memory
Ok : Power Supplies
Ok : Processors
Ok : Temperatures
Ok : Voltages
Ok : Hardware Log
For further help, type the command followed by -?
PE1855:
[root at ccregdub_pr ~]# omreport chassis
Health
Main System Chassis
<----Hobbit gets cut off here
SEVERITY : COMPONENT
Ok : Memory
Ok : Power Supplies
Ok : Processors
Ok : Temperatures
Ok : Voltages
Ok : Hardware Log
For further help, type the command followed by -?
▸
-----Original Message-----
From: Thomas Séglard [mailto:user-358ce494902e@xymon.invalid]
Sent: 26 November 2008 09:48
To: user-ae9b8668bcde@xymon.invalid
Cc: Brian O'Mahony
Subject: Re: [hobbit] Dell OpenMage & hobbit
Hi,
I rewrote a little these scripts to match my setup. Actually, I got a
lot of Dell PE 1850/1950/2950 and so on... In addition, I rewrote
another script to grab informations from the BMC. Please, find below the
output :
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
green Fans : Ok : omreport chassis fans
green Intrusion : Ok : omreport chassis intrusion
green Memory : Ok : omreport chassis memory
green Processors : Ok : omreport chassis processors
green Temperatures : Ok : omreport chassis temps
green Voltages : Ok : omreport chassis volts
green Hardware Log : Ok : none
green Batteries : Ok : omreport chassis batteries
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
green All Server Components Functional !
No need for snmp, only 'sudo' ! Obviously, the OMSA package has to be
installed on your monitored servers.
Sincerly,
ThomaS
Buchan Milne a écrit :On Tuesday 25 November 2008 18:10:37 Brian O'Mahony wrote:Im running two scripts from deadcat.net -- bb-omsa-raid.sh and openmanage.sh. Decided to implement these on a number of servers, and im seeing a few issues: 1. On PE2850s the openmanage script is showing all the information. However the Raid monitor lists the disks and the controllers but reports "no Controllers Found" 2. On PE1850 the openmanage script only picks up "Health" I assume this is picking up the CHASSIS health rather than mainsystem health? Is there a version for blades or do I go edit the script?Have you tried devmon with the dell-poweredge template?
The information in this email is confidential and may be legally privileged. It is intended solely for the addressee. Access to this email by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution or any action taken or omitted to be taken in reliance on it, is prohibited and may be unlawful. If you are not the intended addressee please contact the sender and dispose of this e-mail. Thank you.
list Rakesh Nair
HI all I am in a pethetic condition. I was working on bash-scripting in which I was using twiddle to monitor JBOSS and wrote a bash script which uses data from twiddle to send it to Hobbit usiing the BB tool. But now I am asked to use Java/JMX Programming for monitoring JBOSS. I am not exposed to java programming so can anyone help me by sharing some java programs which can be used for monitoring jboss. Its really an emergency... plse reply ASAP. Thanks Rakz
list Brian O'Mahony
From: Buchan Milne
▸
On Tuesday 25 November 2008 18:10:37 Brian O'Mahony wrote:Im running two scripts from deadcat.net -- bb-omsa-raid.sh and openmanage.sh. Decided to implement these on a number of servers, and im seeing a few issues: 1. On PE2850s the openmanage script is showing all the information. However the Raid monitor lists the disks and the controllers but reports "no Controllers Found" 2. On PE1850 the openmanage script only picks up "Health" I assume this is picking up the CHASSIS health rather than mainsystem health? Is there a version for blades or do I go edit the script?
Have you tried devmon with the dell-poweredge template?
Buchain - I haven't tried devmon. While I wouldn't mind setting it up, I have very little time to spend on this, and I also cannot guarantee that snmp is running. These are live production VOB servers, and to be honest I had to do everything involving the two scripts (bb-omsa-raid.sh && openmanage.sh) in a test environment for a few days to make sure it wouldn't impact them.....
Basically what I have figured out with the scripts:
On my 2850s, there are SCSI cards with no RAID volumes. They show up as red. I want to stop it seeing these cards preferably.
On my 1855s if I run the omreport chassis command I get all the info. However on the hobbit webpage its only printing the first two lines....
▸
The information in this email is confidential and may be legally privileged.
It is intended solely for the addressee. Access to this email by anyone else
is unauthorized. If you are not the intended recipient, any disclosure,
copying, distribution or any action taken or omitted to be taken in reliance
on it, is prohibited and may be unlawful. If you are not the intended
addressee please contact the sender and dispose of this e-mail. Thank you.
list Sebastian Auriol
▸
Thomas Kähn <mailto:user-02a72cb3f725@xymon.invalid> wrote:
Hi Buchan, On Tue, Nov 25, 2008 at 05:42:18PM +0200, Buchan Milne wrote:On Tuesday 25 November 2008 17:02:29 Thomas Kähn wrote:is it possible to run bbproxy and bb-display at the same time?Yes.thanks for your hint regarding my problem. I've tried to run both services. However either bbproxy was not forwarding alarms (when hobbitd was running too) or the web pages on the proxy where not updated. Can you give me a short notice on how to configure bbproxy/hobbitd in order to have a normal Hobbit server running which in addition sends all messages to another Hobbit server? Do I have to set different port numbers for hobbitd and bbproxy? I've already tried to set bbproxy to 1985 which resulted in the problem described above. Best regards Thomas
My entry for bbproxy in hobbitlaunch.cfg is like this: CMD $BBHOME/bin/bbproxy --hobbitd --bbdisplay=<other IP address(es)>,127.0.0.1 --listen=0.0.0.0:1985 --report=$MACHINE.bbproxy --no-daemon --pidfile=$BBSERVERLOGS/bbproxy.pid #--log-details And hobbitserver.cfg: BBDISPLAYS="127.0.0.1 <other IP address(es)>" # IP of multiple hobbit/bbd servers. If used, BBDISP must be 0.0.0.0 Which alarms exactly are not being forwarded? SebA
list Thomas Kähn
Hi SebA,
▸
On Mon, Dec 01, 2008 at 02:49:27PM -0000, SebA wrote:Thomas Kähn <mailto:user-02a72cb3f725@xymon.invalid> wrote:Can you give me a short notice on how to configure bbproxy/hobbitd in order to have a normal Hobbit server running which in addition sends all messages to another Hobbit server? Do I have to set different port numbers for hobbitd and bbproxy? I've already tried to set bbproxy to 1985 which resulted in the problem described above. Best regards ThomasMy entry for bbproxy in hobbitlaunch.cfg is like this: CMD $BBHOME/bin/bbproxy --hobbitd --bbdisplay=<other IP address(es)>,127.0.0.1 --listen=0.0.0.0:1985 --report=$MACHINE.bbproxy --no-daemon --pidfile=$BBSERVERLOGS/bbproxy.pid #--log-details And hobbitserver.cfg: BBDISPLAYS="127.0.0.1 <other IP address(es)>" # IP of multiple hobbit/bbd servers. If used, BBDISP must be 0.0.0.0 Which alarms exactly are not being forwarded?
I forgot to add 127.0.0.1 to the list of BBDISPLAYS. This could have solved my problem. However the setup has been altered and currently there is no forwarding to main Hobbit planned anymore. Thanks for your response. I keep it in mind in case I have to configure a similar setup again.
▸
Best regards
Thomas
--
Thomas Kähn NetCologne
Network Engineering & Design Gesellschaft für Telekommunikation mbH
Im Süsterfeld 6
Telefon: 0241/701333-18 52072 Aachen
Fax: XXXX/XXXXXX
Handelsregister: HRB 25580, Amtsgericht Köln
Geschäftsführer: Werner Hanf, Dipl.-Ing. Karl-Heinz Zankel