xymon-bounces at xymon.com schrieb am 08.12.2011 14:22:07:
Von:
<user-ce4a2c883f75@xymon.invalid>
An:
<xymon at xymon.com>
Datum:
08.12.2011 14:21
Betreff:
Re: [Xymon] Antwort: Re: Windows load triggering only on default
settings?
Gesendet von:
On Thu, 8 Dec 2011 13:47:11 +0100, "Hermann-Josef Beckers"
<user-3e5362deca72@xymon.invalid> wrote:
HOST=%ssnts.*,sspro01 TIME=W:0600:1800
You are trying to mix regular expressions with host lists - I am
quite
sure you don't have any hosts with a comma in the hostname.
"HOST=%ssnts.*|sspro01" should do the trick.
No change. BTW: I think you meant HOST="%ssnts.*|sspro01" (qoutation
mark
after
the equalsign ?). But it makes no difference. I even seperated both
entries
on extra lines with no variable substition. The only change happened
after
upping the DEFAULT values.
Make sure you have the DEFAULT section at the end of the analysis.cfg
file. If you have it before the HOST-specific entries, they will be
ignored.
Is there a way to debug which rules are applied?
...
see the following typescript:
Script wurde gestartet: Do 08 Dez 2011 14:27:06 CET
xymon at lscopy02:~/server/etc> tail -15 analysis.cfg
# Rules are evaluated from the top of this file and down, and the first
# matching rule is used. So you should put the specific rules first, and
# the generic rules last.
# These are the built-in defaults.
DEFAULT
UP 1h
#LOAD 15 25
LOAD 50 75
DISK * 90 95
SWAP 50 80
MEMPHYS 100 101
MEMSWAP 50 80
MEMACT 90 97
xymon at lscopy02:~/server/etc> cd ../bin
xymon at lscopy02:~/server/bin> xymoncmd xymond_client --test
2011-12-08 14:27:42 Using default environment file
/home/xymon/server/etc/xymonserver.cfg
Hostname (.=end, ?=dump, !=reload) []: ssnts1
Hosttype []:
Test (cpu, mem, disk, proc, log, port): cpu
Load: Yellow at 50.00, red at 75.00
Uptime: From boot until 1h ,and after uptime
Hostname (.=end, ?=dump, !=reload) [ssnts1]: ssnts2
Hosttype []:
Test (cpu, mem, disk, proc, log, port): cpu
Load: Yellow at 50.00, red at 75.00
Uptime: From boot until 1h ,and after uptime
Hostname (.=end, ?=dump, !=reload) [ssnts2]: sspro01
Hosttype []:
Test (cpu, mem, disk, proc, log, port): cpu
Load: Yellow at 50.00, red at 75.00
Uptime: From boot until 1h ,and after uptime
Hostname (.=end, ?=dump, !=reload) [sspro01]: .
xymon at lscopy02:~/server/bin> cd -
/home/xymon/server/etc
xymon at lscopy02:~/server/etc> grep -i load analysis.cfg
# LOAD : Changes the "cpu" status according to the system load.
# LOAD warnlevel paniclevel
# If the system load exceeds "warnlevel" or "paniclevel", the
"cpu"
LOAD 60.0 80.0
LOAD 60.0 80.0
LOAD 60 80
# LOAD 60 80
# LOAD 8.0 12.0 HOST=db.foo.com TIME=*:0800:1600
# LOAD 8.0 12.0
# LOAD 7.0 12.0 HOST=bax.foo.com
# LOAD 3.0 8.0
# will result in the load-limits being 7.0/12.0 for the "bax.foo.com"
host,
#LOAD 15 25
LOAD 50 75
xymon at lscopy02:~/server/etc> exit
exit
Script beendet: Do 08 Dez 2011 14:28:49 CET